PureVolume

 
Next »
 
 

How to Install a synthetic Grass Lawn

blog post

alt

We are best Supply the high quality plastic materials products for Green Roofs, Grass Ground Reinforcement, environmental greening solutions, landscape construction, etc. suppliers,we supply best Supply the high quality plastic materials products for Green Roofs, Grass Ground Reinforcement, environmental greening solutions, landscape construction, etc. products for sale.

Once you have completed the preparation stage including measuring how much artificial grass you need, installing appropriate drainage (if necessary) and removing the natural grass layer, you will be ready to install your artificial grass lawn. This informative article outlines the steps you ought to follow to help you to complete the job right, from laying the bottom, connecting joints and preventing unwanted weeds. artificial grass

Lay Gravel Base followed by Sharp Sand

If needed, use treated timber/timber stakes to do an area frame. We suggest 4 X Two inches of tantalised treated timber for heavy clay soil areas and poorly draining areas and two X 2 inches of tantalised timber forever draining areas. Screw these timbers towards the stakes leaving the stakes within the perimeter. If the Artificial Grass meet a concrete path, wall or decking, placed the timber flush with all the surface height and also by using 10mm temporary fillet, pack the timber close to the wall leaving the space to enable you to tuck the unreal Grass between the timber along with the adjoining material in a later stage.

Placed the stakes against the inner perimeter timber edging and hammer into the ground ensuring the stakes are slightly under the timber edging. Next screw the timber stake towards the timber edging.

With heavy clay soils we recommend laying a crushed stone the surface of up to 3 inches. This will likely not be necessary for the majority of areas and only required if you have a high water table in which the ground holds water for a long period of time after it rains. Next compact the soil using a vibrating plate that could be hired from an equipment hire company. Ensure the perimeter is compacted and under the timber edging by 1 ". Infill the perimeter with sharp sand and level employing a rake. Ensure the sand is level up of the timber edging small again. gravel grid

For good drainage areas spread a layer of sharp sand to blind in the soil. Next compact the soil using a vibrating plate that could be hired from a tool hire company. Ensure the perimeter is compacted and level together with the timber edging.

If you put more operate in at this stage, your Artificial Grass Lawn will look better as a result.

Weed Control Layer

Use the weed control geo textile membrane and cut as necessary. Tack using small 1 " galvanised clout nails on the timber edging. This weed control geo textile membrane prevents any chance of weed growth through the artificial grass drainage holes.

Unveil Artificial Grass

Lay the unreal Grass in the desired direction working on the carpet and not for the levelled base. Ensure the carpet is put to minimise cuts, joints and waste overlaying the timber edging by way of a minimum of 4 inches. In the event the artificial grass meets a path or edge, of course, if you have laid the timber edging correctly as previously described, then this artificial grass may be wedged between. If joining, please be sure that the artificial grass is laid using the pile running within the same direction on each piece. Lay carpeting on top of the sand instead of dragging it throughout the base material. To aid stop wrinkles or creasing you need to allow 2 to 3 hours to stay before continuing with jointing and adhesive. Cut grass to shape by using a sharp Dolphin or Stanley knife or scissors.

Jointing

When jointing your outdoor carpet together, ensure that the pile runs within the same direction. Take off manufacturer's edge strip (if present) and butt two edges together ensuring there are no gaps greater than 1mm between the two carpet edges. The truth of this will determine how visible the join is after the completion. Fold back edges and position jointing tape (smooth side down) in order that the edges of the carpet meet the tape when joined.

Adhesive

a) Use the cartridge adhesive inside a zig zag motion onto the rougher side with the tape allowing one cartridge for every single 3 linear metres. Ignore carpet and press both edges into the wet adhesive, ensuring each bit marries up and has no overlap. As you are doing this with your fingers, mix the fibres together to conceal the join. When the whole length is within place and you are very pleased with its appearance it is necessary to walk along the join many times to activate the glue and bond the grass to the tape. Weigh down the seam to make certain good contact with the glue until it cures. The harder care taken together with the operation the neater and tidier the joint will probably be.

or

b) If with all the 2-component multi-purpose adhesive, ensure thorough mixing of the two components before use. Apply adhesive towards the rough side with the tape and spread evenly across a width for at least 20cm using if possible a notched trowel. Sufficient adhesive must be applied so that in the event the artificial grass carpet is pressed into the adhesive, a transfer on the carpet backing is done. Turn down carpet and press both edges in to the wet adhesive, ensuring each bit marries up and has no overlap. Ensure the carpet does not crest at the seam and is holding flat on the bonded area. Once the whole length is place and you are very pleased with its appearance it's important to walk along the join more than once to activate the glue and bond the grass to the tape. Weight the seam to make sure good contact with the glue until it cures. The greater care taken using the operation the neater and tidier the joint will be.

While you should endeavour to not put adhesive onto the carpet small amounts of glue can be removed from the artificial grass fibre using White Spirit and a small off cut in the artificial grass. Small quantities of cured glue normally can be removed. To prevent situation and the chance of damage to the artificial grass, care and precautions should be taken to avoid contact with the fibres at all times.

When the artificial grass may be jointed and glued and you really are happy with the levels screw the grass to the timber perimeter framework using galvanised screws to start of 12 inch intervals.

Spread Sand (Optional, depending on Grass Selected)

If the artificial grass may be laid use silica sand, which can be kiln dried and brush into carpet as you go. Each product would have sand infill but this is merely used to stabilise the rug and at no time if the sand be visible. You must obtain an even spread in the surface using a brush to build up the depth in layers. Do not apply the sand in a single application. Brush sand into pile immediately after laying while the artificial grass is dry although weather is good. Brush vigorously contrary to the fibres of the carpet pile to inspire the tufts to stand upright. Putting the correct amount of sand in helps retain the artificial grass to sleep down, protects the fibres plus keeps them standing take the look of real grass.

As soon as the hard work has been done, you'll be able to sit back and relax knowing your artificial grass lawn will be great and require minimal maintenance.

Contact:
Leiyuan Industrial Company Limited
The nearest air port:Jinjiang Air Port & Xiamen International Air Port
MSN: leiyuan08@hotmail.com
Skype: leiyuan08
+86-595-2278 8697
+86-595-2277 8697
sales08@greening-solution.com
alan@greening-solution.com

 

Posted Nov 14, 2015 at 12:03am

0 likes

 

Comments

 
 
1