PureVolume

 
 
 
Blog Post
 

The shower can be quite a very scary place when those soap suds start to gather on the ground of one's shower. Going To spikes perhaps provides cautions you might use with your cousin. One way to feel safer in the shower is to use a grab bar to the wall. Listed below are the tools you'll need and recommendations to correctly install a grab bar in your tiled bathroom shower.

After a grab bar has been acquired by you you need to obtain the various tools needed seriously to install it. Listed here are the equipment you will need:

Philips-head screwdriver

Drill

1/8 inch masonry bit or glass and tile bit

Stud finder or perhaps a period of wire

Record measure

Silicon caulk

Sharp awl or carbide glass and tile punch touch

Wood bit, 1/16 smaller compared to the size of mounting screws

First thing that you will need to do to install your grab bar is to find a wall stud. This can help considerably when you yourself have usage of a stud finder. Run the stud finder across the wall until a wall stud is found and mark the spot with a fine point marker. Should you not need a digital stud finder, no concerns, just take a masonry bit or glass and tile bit and just punch a hole in to the grout. Then simply take your length of cable and produce a bend in it. Set the cord in the hole and by spinning it left and right you should hit a stud. The opening that you just drilled could be filled with a small bit of silicone caulk, if a stud was not located by you. Be sure to flatten the dab of silicone caulk so that it doesn't protrude from the grout line, permit the caulk to dry for around three hours. Mix up a bit and repair the hole, If you have powdered grout useful. Re-drill another hole until you locate a stud. For additional information, people are able to check out: follow us on twitter. When you do locate a stud, measure 16 inches from that hole and you must certanly be in a position to drill into another stud.

So that you can determine from the beds base of the tub to look for the keeping your bar you will wish to indicate your stud areas. Place your club so that each end is over a stud and mark the screw holes that come in the mounting bracket.

To drill the mounting holes into tile you'll have to produce a starting point for the drill bit if not the bit will stumble upon the tile. Learn further on punk rock by going to our refreshing paper. For supplementary information, people can gaze at: site preview. To produce a starting place work with a sharp awl or afore stated drill bit. Utilizing your hand, twist the device on your make to make a small impression on the tile; your drill bit will be kept by this from slipping. Do not work with a value or you are more likely to split your tile. Use your hole to be drilled by the glass and tile bit. Place tape on the tile, if using a masonry bit and routine slowly in order to avoid shattering the tile. You dont desire to break your tiles when screwing the mounting brackets on both therefore work with a bit that's 1/32 larger compared to the size of the mounting screw you'll be using. Begin drilling the hole slowly and with even pressure whilst to not slip off your mark. Use light pressure when drilling in order to avoid cracking the tile.

Make sure to not drill deeper compared to tile and it assistance. At this point, you will need certainly to modify your bit to the wood bit 1/16 narrower compared to the screw. A pilot hole will be made by this in the guys.

The ultimate step is always to support the bar. Silicone caulk will need to be applied to the pockets before mounting; this really is to safeguard the backing and wood boards behind the tiles from leaking water. Just attach the bar to the wall. You'll want to use metal screw or they will rust. Tighten the screws tightly making certain to not over tighten them or they'll crack the tile.

You should now have your grab bar correctly fitted. You can now have a peaceful, relaxing shower and feel better in the process..

Posted Jun 30, 2017 at 1:26pm

Comments

 
 

Friends (1)

 

Posts (9873)

 
Signup for PureVolume, or Login.